查看: 1274|回复: 6
大麦DW33D ,TTL救砖求指导.
本帖最后由 xjw1162 于
20:31 编辑
碰到的问题是:&&无法ping通路由器.
开机引导信息
eth1 up
eth0, eth1
Atheros on-chip NAND FLash Controller Driver, Version 0.1 (c) 2010 Atheros Communications, Ltd.
Ath Nand ID[8ffee17c]: 2c:f1:80:95:04
ONFI MICRON& && &MT29F1G08ABAEAWP& &
Micron NAND 128MiB 3,3V 8-bit [128MB]
====== NAND Parameters ======
sc = 0x8ffee158 bbt = 0x8ff9c538 bbt_size = 0x100 nf_ctrl = 0x344
page = 0x800 block = 0x20000 oob = 0x40
size = 128MB
Setting 0x to 0x58b0214f
last reboot failed.
NAND read: device 0 offset 0x6000000, size
...&& bytes read: OK
CRC32 for
... 80f9ffff ==& b7190af0
Erasing flash...
First 0x5 last 0xfe sector size 0x10000
254
Erased 250 sectors
Copy to Flash... write addr: 9f050000复制代码
不知道为什么一开机就erasing flash.
然后进入命令模式
ath& bdinfo
boot_params = 0x8FF6BFB0
memstart& & = 0x
memsize& &&&= 0x
flashstart&&= 0x9F000000
flashsize& &= 0x
flashoffset = 0x
ethaddr& &&&= 00:AA:BB:CC:DD:EE
ip_addr& &&&= 192.168.1.1
baudrate& & = 115200 bps复制代码
mac地址有点奇怪.
有个tftpboot命令
ath& tftpboot
Trying eth0
eth0 link down
FAIL
Trying eth1
dup 1 speed 1000
*** Warning: using 's'
Using eth1 device
TFTP from server 192.168.1.10; our IP address is 192.168.1.1
Filename '.img'.
Load address: 0x复制代码
这个意思就是网线插在eth1中,终端指定IP为192.168.1.10
服务器ip为192.168.1.1
文件名.img
无法ping通路由器,目前不知道怎么操作,求教导
完整的命令行支持
ath& help
?& && & - alias for 'help'
autoscr - run script from memory
base& & - print or set address offset
bdinfo&&- print Board Info structure
boot& & - boot default, i.e., run 'bootcmd'
bootd& &- boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm& &- boot application image from memory
bootp& &- boot image via network using BootP/TFTP protocol
bootvx&&- Boot vxWorks from an ELF image
cmp& &&&- memory compare
coninfo - print console devices and information
cp& && &- memory copy
crc32& &- checksum calculation
dhcp& & - invoke DHCP client to obtain IP/boot params
echo& & - echo args to console
erase& &- erase FLASH memory
ethreg&&- Switch/PHY Reg rd/wr&&utility
exit& & - exit script
flinfo&&- print FLASH memory information
go& && &- start application at address 'addr'
help& & - print online help
iminfo&&- print header information for application image
itest& &- return true/false on integer compare
loop& & - infinite loop on address range
mct& &- simple RAM test
md& && &- memory display
mii& &&&- MII utility commands
mm& && &- memory modify (auto-incrementing)
mtest& &- simple RAM test
mw& && &- memory write (fill)
nand& & - NAND sub-system
nboot& &- boot from NAND device
nfs& &&&- boot image via network using NFS protocol
nm& && &- memory modify (constant address)
pci& &&&- list and access PCI Configuration Space
ping& & - send ICMP ECHO_REQUEST to network host
pll cpu-pll dither ddr-pll dither - Set to change CPU & DDR speed
pll erase
pll get
printenv- print environment variables
progmac - Set ethernet MAC addresses
progmac2 - Set ethernet MAC addresses
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset& &- Perform RESET of the CPU
run& &&&- run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv&&- set environment variables
sleep& &- delay execution for some time
test& & - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version - print monitor version复制代码
他自带uboot版本:U-Boot 1.1.4-gfacc17ef-dirty (Sep&&4 2015 - 17:55:33)
setenv bootcmd bootm 0x9fe80000
再请教下.怎么在ssh中刷不了breed
:/tmp# cat /proc/mtd
mtd0: 10000 "u-boot"
mtd1: 10000 "u-boot-env"
mtd2: 00e00 "rootf&
非常感谢H大大,
已经自动恢复成原厂固件.
ttl中是root身份登录.
已经使用passwd修改了root密码.也成功开启了ssh.
正在研究刷你的breed&
setenv bootcmd bootm 0x9fe80000
非常感谢H大大,
已经自动恢复成原厂固件.
ttl中是root身份登录.
已经使用passwd修改了root密码.也成功开启了ssh.
正在研究刷你的breed
本帖最后由 xjw1162 于
01:37 编辑
setenv bootcmd bootm 0x9fe80000
再请教下.怎么在ssh中刷不了breed
:/tmp# cat /proc/mtd
dev:& & size& &erasesize&&name
mtd0: 10000 &u-boot&
mtd1: 10000 &u-boot-env&
mtd2: 00e00 &rootfs&
mtd3: 10000 &kernel&
mtd4: 10000 &art&
mtd5: 00f00 &firmware&
mtd6: 20000 &rootfs_data&
mtd7: 20000 &backup&
第一个第二个不知道写入哪个
#mtd -r write ./dw33d.bin Bootloader
Could not open mtd device: Bootloader
Can't open device for writing!
用u-boot 或者mtd0 或者 u-boot-env 都报错.
最后又回到ttl u-boot模式中
使用tftp成功上传到u-boot.
但是没有任何反应.重启之后还是boot.
你这个是固件没解锁的提示,请刷解锁固件 然后 ssh进去,mtd write breed-qca9558-dw33d.bin u-boot
群里有固件 欢迎你,&
再请教下.怎么在ssh中刷不了breed
:/tmp# cat /proc/mtd
你这个是固件没解锁的提示,请刷解锁固件 然后 ssh进去,mtd write breed-qca9558-dw33d.bin u-boot&&群里有固件 欢迎你,
谢谢分享！！
Powered by查看: 3618|回复: 3
又一个大麦DW33D千兆路由可刷固件
本帖最后由 Vxworks 于
13:30 编辑
又一个同方案的&&
官方固件&&
Instruction set:& && &&&MIPS
Vendor:& && &&&Qualcomm Atheros
Bootloader:& && &&&U-Boot
System-On-Chip:& && &&&QCA9558-AT4A Rev 2
CPU @Frq& && &&&MIPS 74Kc Vers. ?.? @720MHz
Flash size:& && &&&16 MiB
Flash Chip:& && &&&Macronix MX25L12845EMI-10G
RAM size:& && &&&2* 128 MiB
RAM Chip:& && &&&Nanya NT5TU64M16GG-AC
Wireless No1:& && &&&SoC-integrated: QCA9558-AT4A w/ 3x3 MIMO for 2.4GHz 802.11b/g/n
Wireless No2:& && &&&Mini PCI-e: QCA9880-BR4A w/ 3x3 MIMO for 5GHz 802.11a/n/ac
Switch:& && &&&Qualcomm Atheros QCA8337-AL3C (Gigabit, VLAN)
Modem:& && &&&none
USB:& && &&&Yes 1 x 2.0
Serial:& && &&&Yes
JTAG:& && &&&?
U-Boot 1.0.0 (May 23 2013 - 17:15:24)
Product Name: ESR
ap136 - Scorpion 1.0
DRAM:256 MB
Now running in RAM - U-Boot at: 8ffc8000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
Flash size 16MB, sector count = 256
In:& & serial
Out:& &serial
Err:& &serial
reset_switch:
reset_usb:
Multi Net:
ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0xe
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion&&----& S17 PHY *
: cfg1 0x cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs17_reg_init: SUPPORT_QCA8337
athrs17_reg_init: QCA8337 ID=1302
athrs17_reg_init: complete
athrs17_disable_all_port
Setting 0x to 0x60c0214f
Please choose the operation:
& &1: Load system code to SDRAM via TFTP.
& &3: Boot system code via Flash (default).
3: System Boot system code via Flash.
athrs17_set_portvlan_isolated complete
## Booting image at 9f040000 ...
& &Image Name:& &Linux Kernel Image
& &Created:& && && &6:59:16 UTC
& &Image Type:& &MIPS Linux Kernel Image (lzma compressed)
& &Data Size:& & 1867435 Bytes =&&1.8 MB
& &Load Address:
& &Entry Point:&&802ad4d0
& &Verifying Checksum at 0x9f040040 ...OK
& &Uncompressing Kernel Image ... OK
Starting kernel ...
Booting QCA955x
init started: BusyBox v1.7.5 ( 14:50:11 CST)
starting pid 807, tty '/dev/console': '/sbin/config_init'
mknod: /dev/ttyS0: File exists
mknod: /dev/ttyS1: File exists
Config Init version: 1.1.0.23 date:
Tue Jan&&1 00:00:00 UTC 2013
ln: /lib/./modules: File exists
starting pid 867, tty '/dev/ttyS0': '/sbin/config_term'
[sysUtil] Hardware ID -
[sysUtil] Load vendor[1] information
************************************************************************
*& && && && && && && && && && && & ESR1750& && && && && && && && && &&&*
************************************************************************
KernelApp/Ramdisk Ver:1.1.0.23& && && && && && & Date:
本帖最后由 ntgeralt 于
14:16 编辑
手上有大麦，支持一下，不过路由不在手上，有空拿来试试
百度云的 openwrt固件
固件能再分享么？&
大麦路由刷机交流群& &
手上有大麦，支持一下，不过路由不在手上，有空拿来试试
百度云的ESR1750 openwrt固件
http://pan.baidu. ...
固件能再分享么？
Powered by